Eiki NPC-1 Bedienungsanleitung Seite 1

NPC-1TCP/IP Network Projector ControlQuickLogix™ NetControl 1.0 Starter PackageGetting Started GuideJapan & WorldwideEIKI Industrial Co., Ltd.4-12

- 8 -Getting StartedNow that you have been introduced to NPC-1’s features and specifications, it is time toset up the hardware, install the software,

- 9 -Connecting the NPC-1 to a networkThere are two ways to use the 10/100BaseT Ethernet jack located on NPC-1’s frontpanel:1. For most applications u

- 10 -Changing Network PropertiesSelecting a NPC-1 deviceClick on the menu Tools|Network Properties to get a list of all NPC-1 devices on yournetwork.

- 11 -Changing the projector locationChange the projector location to the location where the projector is installed. E.g.“Meeting Room 3” or “Building

- 12 -Changing the subnet maskThe NPC-1 device is shipped with the following default subnet mask: 255.255.255.0Change the subnet mask of the NPC-1. If

- 13 -DHCP settingThis topic is applicable if you are using a DHCP (Dynamic Host Configuration Protocol)server in your network. This type of server is

- 14 -Searching the networkSearch the NetworkClick on the menu Search|Search Network to do a network search for NPC-1 devices.You can perform the same

- 15 -Connecting to a ProjectorChoosing a valid IP addressBefore you can work with your projector on the network you have to type a valid IPaddress in

- 16 -Connecting to a projectorBefore you can work with your projectors on the network you have to pick a valid IPaddress and a projector model from t

- 17 -Reading the Status of a ProjectorAm I connected?To get a status reply from your projector you have to be connected to a projector. If yourare n

cover.pmd 2/13/2003, 2:39 PM1

- 18 -Not all status requests are available with every projector model.Missing replies will be indicated.manual.pmd 3/18/2003, 6:32 PM18

- 19 -Controlling the ProjectorUsing control features of the projectorTo control a projector the NetControl software has to be connected to a projecto

- 20 -Why are some buttons deactivated?Buttons are normally deactivated when the NetControl software is not connected to aprojector. You have to conn

- 21 -Cable PinoutsRS232RS232 standards are defined by EIA/TIA (Electronic Industries Alliance /Telecommunica-tions Industry Association). RS232 defin

- 22 -Software License AgreementPLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("LICENSE") CAREFULLY BEFOREUSING THE SOFTWARE. IF YOU DO NOT AG

- 23 -CORRECTED. FURTHERMORE, QUICKLOGIX DOES NOT WARRANT OR MAKE ANY REPRE-SENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE QUICKLOGIXSO

- 24 -Declaration of ConformityWe,EIKI Industrial Co., Ltd.4-12 Banzai-Cho, Kita-KuOsaka 530-0028Japandeclare under our sole responsibility that the p

cover.pmd 2/13/2003, 2:39 PM1

NPC-1TCP/IP Network Projector ControlQuickLogix™ NetControl 1.0 Starter PackageGetting Started GuideJapan & WorldwideEIKI Industrial Co., Ltd.4-12

- 1 -NPC-1Network Projector ControlandNetControlTM 1.0 Starter PackageGetting Started GuideFirst Edition, March 2003manual.pmd 3/18/2003, 6:32 PM1

- 2 -The software described in this manual is furnished under a license agreement and maybe used only in accordance with the terms of this agreement.C

- 3 -Table of ContentsIntroduction ...

- 4 -manual.pmd 3/18/2003, 6:32 PM4

- 5 -IntroductionWelcome to NPC-1, a compact palm-sized control device that allows you to control andmaintain projectors and other audiovisual equipme

- 6 -Technical SpecificationsHardwareProcessor 16 bit processor, 80186Memory 512 KBSerial Connector Male DB9, DTEInterfaceLAN Auto-detecting 100Base-T

- 7 -Package ChecklistIf you purchased the NetControl software along with the NPC-1 device you should findthe follwing items in your shipping box:• NP