Eiki LC-XT1 Bedienerhandbuch

MULTIMEDIA PROJECTOR MODEL LC-XT1 OWNER’S INSTRUCTION MANUAL

LC-XT1 .

LC-XT1 . This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers a

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 2 TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many c

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 . TURNING ON THE PROJECTOR 1.Complete the peripheral connections (with Computer, VCR, etc.) before turning on the projector. (Refer to “CON

LC-XT1 .

LC-XT1 .

LC-XT1 .

LC-XT1 . When connecting to the computer, select a computer signal type (Digital or Analog) in INPUT SOURCE Menu. 1 Press the MENU button and the

LC-XT1 .

LC-XT1 .

LC-XT1 3 SAFETY PRECAUTIONS All the safety and operating instructions should be read before the product is operated. Read all of the instructions

LC-XT1 . This Projector can automatically tune to the display signals from most personal computerscurrently distributed. However, some computers e

LC-XT1 . Total lines The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total dots The number

LC-XT1 . NOTE: The Fine sync and the Total dots cannot be operated when the input signal is digital from DVI terminal or “RGB” is sel

LC-XT1 . ‘-‘C’’ The AUTO IMAGE function cannot be operated when the input signal is digital from DVI terminal or “RGB”, “480p”, ‘575p”, “HDTV7

LC-XT1 . 1 Press the MENU button and the ON-SCREEN MENUwill appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button

LC-XT1 . When connecting to those equipment, select the type of Input source in INPUT SOURCE Menu. 1 Press the MENU button and the ON-SCREEN MENU

LC-XT1 . 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SE

LC-XT1 .

LC-XT1 .

LC-XT1 . 1Press the MENU button and the ON-SCREEN MENUwill appear. Press the POINT LEFT/RIGHT buttonsto select SETTING and press the SELECT button.

LC-XT1 4 COMPLIANCES Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digita

LC-XT1 . On start When this function is “On” the projector is automatically turned on just by switching the MAIN ON / OFF SWITCH on. NOTE: Be sure

LC-XT1 . 1 Turn the projector on, and press the MENU button and the ON- SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to se

LC-XT1 . NOTE: When the computer has no mouse port, connect the Serial Port of the computer to Control Port of the projector with the Control Cable

LC-XT1 . computer is switched on first, the Wireless Mouse may not work properly. The TEMPERATURE WARNING Indicator flashes red when the internal t

LC-XT1 . This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp Management Function. La

LC-XT1 . Follow these steps to replace the lamp assembly. 1 Check the number of lamp to be replaced on Lamp Status Display.2 Turn off the proje

LC-XT1 . Before calling your dealer or service station for assistance, check the items below once again. 1. Make sure you have connected the proje

LC-XT1 .

LC-XT1 .

LC-XT1 . HDB 15-PIN TERMINAL (ANALOG) Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). • When c

LC-XT1 . TABLE OF CONTENTS FEATURES AND DESIGN 6 PREPARATION 7NAME OF EACH PART OF THE PROJECTOR 7SETTING-UP THE PROJECTOR 8CONNECTING THE AC POW

LC-XT1 .

LC-XT1 .

LC-XT1 . • Compatibility This projector widely accepts various video and computer input signals including; • Computers IBM-compatible and Macintos

LC-XT1 .

LC-XT1 . This projector uses nominal input voltages of 100-120V or 200-240 V AC. The projector automatically selects the correct input voltage. It

LC-XT1 . Before setting up the projector, install the Projection Lens on the Projector. 1.Before installation, check where the projector is used an